450
Cookies help us deliver our services. By using our services, you agree to our use of cookies.
Accept Cookies Learn MoreLot
450
Melting Furnace...Has approximately 16,000 to 18,000 thousand pounds of aluminum inside) has a bath volume calculated to contain 162,835lbs of molten aluminum at a design temp of 1350 F and a density of 145 lbs. per CF when filled to within 4" of the lower edge of the door sill. There is 99,615 lbs. of the full load that is available for tap off. leaving 63,220 lbs. as a heel below the invert of the tap port. the above is based on an average bath depth of 35 1/2". The combustion system is sized for a melt rate of 17,000 lbs./hr. based on 17,000 lb./hr. of scrap aluminum @ 400 F to 1,000 F being fed into the well. The meter will discharge molten aluminum at approx. 1,350 F at a specific rate of 0-2,000 lbs./minute through a pair of tap holes through an open trough to the tilting furnaces. a Metallic molten metal pump located in the well will maintain a recirculation of the metal through the furnace. The enclosure is a refractory lined steel box with a pair of North American Mfg. Co. TwinBed II Regenerative burners, mdl 4343-12-AXX, 12" (12A size) with one burner on each side of the flue. a full width Guillotine type access (skim) door opposite the tap out side of the furnace. The combustion chamber size is 20' x 20' 6" with a height of 5' 7" measured from the top of a full bath to the underside of the roof. The well is 5' wide. door sill is 3' wide and slopes down slightly to the inside of the furnace. a 45degree ramp slopes down from the sill to the hearth. Both the sill and the ramp run the full 20' width of the furnace. Auto fire or forward fire, Auto fire is regenerative firing, Combustion air supplied by a Spencer Turbine Co. blower rated @ 303,840 scfh air at 33 in WC pressure @ 400' elevation controlled by a single motorized 12" wafer type butterfly valve. The blower includes a 50hp 3,600 rpm TEFC motor, furnace exhaust blower is a Spencer Turbine Co. rated @ 3,614 ACFM @ 400 F @ 28" wc static pressure @ 400' above sea level, it includes a 40hp, 3600rpm, TEFC high efficiency coupled motor. Burner exhaust is controlled on the inlet side of the exhaust blower with a motorized 14" wafer type butterfly valve. Natural gas controlled by a 4" motorized adjustable port valve. olten metal pump is a Metallic L-45SD Pump designed to recirculate a maximum of 11,000 lbs. per minute of molten aluminum in the side well of the melting furnace. system includes an electric motor rated @ 28.5 hp and a pump cooling air fan. Furnace roof high temp limit control Honeywell #DC200H-2-000-1F0000-0 fuel shut off it temps become excessive
For Stuart B. Millner & Associates delivery information please telephone 636-744-1400.
****THIS IS NOT YOUR REGISTRATION****. THIS DOCUMENT IS SO THAT WE MAY APPROVE YOU TO BE ABLE TO BID. ALL REGISTRANTS MUST PRINT THESE TERMS OUT, SIGN AND DATE AND RETURN THEM BY FAX TO 636-744-1403 OR BY SCAN AND EMAILING, PRIOR TO BEING APPROVED TO PARTICIPATE IN THIS AUCTION.
At the end of the Terms and Conditions we need the following,
Signor understands that by agreeing and signing these terms and conditions they are binding themselves personally, their company and anyone who uses their user name and password to participate in this auction and confirming that they are authorized to bind there company to the terms and conditions.
Printed Name____________________________
Signature_____________________
Company Name___________________________
Address_______________________
City_____________ State_____ Zip_________ Country_____________
Phone________________________
Mobile Phone________________________________
Fax Number___________________________________
Email Address______________________________
Tax Exempt YES NO If yes, enter tax number and state__________________________Please fax exempt cert.
Sale / Event Date_______________ and/or Location__________________
BidSpotter Customer Service Support Department
To reach a member of our qualified support staff regarding information or questions pertaining to the bidding process; please reach us by phone, email or LiveChat
Auction Terms & Conditions
“By my signature below, I acknowledge that my bid is a legally binding contract and agree to be responsible for payment in full of all related invoices.”
________________________________________ ____________ _______________
Buyer’s Signature Date Buyer #
Your question has been sent to the auctioneer.
There was an error sending your enquiry, why not try again later
Melting Furnace...Has approximately 16,000 to 18,000 thousand pounds of aluminum inside) has a bath volume calculated to contain 162,835lbs of molten aluminum at a design temp of 1350 F and a density of 145 lbs. per CF when filled to within 4" of the lower edge of the door sill. There is 99,615 lbs. of the full load that is available for tap off. leaving 63,220 lbs. as a heel below the invert of the tap port. the above is based on an average bath depth of 35 1/2". The combustion system is sized for a melt rate of 17,000 lbs./hr. based on 17,000 lb./hr. of scrap aluminum @ 400 F to 1,000 F being fed into the well. The meter will discharge molten aluminum at approx. 1,350 F at a specific rate of 0-2,000 lbs./minute through a pair of tap holes through an open trough to the tilting furnaces. a Metallic molten metal pump located in the well will maintain a recirculation of the metal through the furnace. The enclosure is a refractory lined steel box with a pair of North American Mfg. Co. TwinBed II Regenerative burners, mdl 4343-12-AXX, 12" (12A size) with one burner on each side of the flue. a full width Guillotine type access (skim) door opposite the tap out side of the furnace. The combustion chamber size is 20' x 20' 6" with a height of 5' 7" measured from the top of a full bath to the underside of the roof. The well is 5' wide. door sill is 3' wide and slopes down slightly to the inside of the furnace. a 45degree ramp slopes down from the sill to the hearth. Both the sill and the ramp run the full 20' width of the furnace. Auto fire or forward fire, Auto fire is regenerative firing, Combustion air supplied by a Spencer Turbine Co. blower rated @ 303,840 scfh air at 33 in WC pressure @ 400' elevation controlled by a single motorized 12" wafer type butterfly valve. The blower includes a 50hp 3,600 rpm TEFC motor, furnace exhaust blower is a Spencer Turbine Co. rated @ 3,614 ACFM @ 400 F @ 28" wc static pressure @ 400' above sea level, it includes a 40hp, 3600rpm, TEFC high efficiency coupled motor. Burner exhaust is controlled on the inlet side of the exhaust blower with a motorized 14" wafer type butterfly valve. Natural gas controlled by a 4" motorized adjustable port valve. olten metal pump is a Metallic L-45SD Pump designed to recirculate a maximum of 11,000 lbs. per minute of molten aluminum in the side well of the melting furnace. system includes an electric motor rated @ 28.5 hp and a pump cooling air fan. Furnace roof high temp limit control Honeywell #DC200H-2-000-1F0000-0 fuel shut off it temps become excessive
For Stuart B. Millner & Associates delivery information please telephone 636-744-1400.
****THIS IS NOT YOUR REGISTRATION****. THIS DOCUMENT IS SO THAT WE MAY APPROVE YOU TO BE ABLE TO BID. ALL REGISTRANTS MUST PRINT THESE TERMS OUT, SIGN AND DATE AND RETURN THEM BY FAX TO 636-744-1403 OR BY SCAN AND EMAILING, PRIOR TO BEING APPROVED TO PARTICIPATE IN THIS AUCTION.
At the end of the Terms and Conditions we need the following,
Signor understands that by agreeing and signing these terms and conditions they are binding themselves personally, their company and anyone who uses their user name and password to participate in this auction and confirming that they are authorized to bind there company to the terms and conditions.
Printed Name____________________________
Signature_____________________
Company Name___________________________
Address_______________________
City_____________ State_____ Zip_________ Country_____________
Phone________________________
Mobile Phone________________________________
Fax Number___________________________________
Email Address______________________________
Tax Exempt YES NO If yes, enter tax number and state__________________________Please fax exempt cert.
Sale / Event Date_______________ and/or Location__________________
BidSpotter Customer Service Support Department
To reach a member of our qualified support staff regarding information or questions pertaining to the bidding process; please reach us by phone, email or LiveChat
Auction Terms & Conditions
“By my signature below, I acknowledge that my bid is a legally binding contract and agree to be responsible for payment in full of all related invoices.”
________________________________________ ____________ _______________
Buyer’s Signature Date Buyer #