75
Lot
75
1 Used All food equipment oven
Model: KHG-75
Quantity of GAS heated Backing Plates: 75 pairs.
Baking Plate Size: 470mm x 325mm
The pattern of the wafer sheet: 2.5×2.5×0.5 (Standard),
Wafer sheet weight: 50-65g
Output: Up to 38 Sheets /min.
LPG consumption: 20m³ / hour max.
LNG consumption: 60m³ / hour max.
Compressed air consumption: 0.2m³/min /0.8Mpa. Pressure
Burner Mfg.: Kehua
Materials: Pipeline is Stainless Steel, Burners are GG25 Precision cast iron
General Info:
The baking oven is the most important machine in the whole wafer production line. Its mechanical drive system uses baking tongs with hinges, which run on rails inside the oven, and baking plates are attached to the baking tongs. The speed of tong carriage is controlled by the frequency converter, the batter deposit system is batch-type, and the wafer baking system uses LPG for heating of the baking plates.
The functions of the baking oven are fully automatic from spreading batter on the plates until baked wafer sheets come out of the oven. The wafer sheets are baked evenly and produce good quality wafer sheets for the next procedure. There is a PID controller built into the PLC which is used to control the temperature of the baking plates automatically. The collection of the required signal of PID is supplied by an infrared sensor. The oven status display and the data reset are activated through the touch screen. All motors have a starting current protection and thermal overload protection. There’s also a ventilation door.
3-1. Model KHG-75 Gas Oven
The baking oven is the most important machine in the whole wafer production line. The oven is in wholly frame structure, which supplies enough support. Its mechanical drive system adopts baking tongs with hinges, which runs on the rails inside the oven and baking plates are installed in the baking tongs. The speed of tong carriage is controlled by the frequency converter, the batter deposit system is batch-type, and the wafer baking system uses LPG for heating of the baking plates. The functions of the baking oven is fully automatic from spreading batter on the plates through until baked wafer sheets come out of the oven. Bake the wafer sheets evenly and produces good quality wafer sheets for next procedure. In PLC there is a PID controller which is used for controlling the temperature of the baking plates automatically. The collection of required signal of PID is supplied by an infrared sensor. The oven status display and the data reset are supplied by a touch screen. All motors have the starting current protection and thermal overload protection. There’re ventilation door.
The gas accessories meet the standard of FM approval, and there’s one alarm if the gas leaking. There’re two ways of temperature controlling: one for testing the baking plates, another for testing the baking chamber, both of them can be showed of the touch panel and you just need to choose one. They’re sealed by silica gel.
There are two set of centrifugal fan on the top of oven for exhaust gas.
AC contactor is supplied by SCHENEIDER.
The stepping wheel bearings of the mould rack are supplied by SKF .
The pressing roller bearings are supplied by SKF.
Main Pneumatic components are supplied by FESTO.
The main drive reducing motor is supplied by SEW, in the front of baking oven with waste withdraw ahead and automatic tightening. Oven track is of 45#heat treatment, size 25X25.
The top of electrical cabinet is inclined 45 º, plus four Φ65 round leg (heigh 400 ). There’re data box, explosion-proof lamp, 2-3 socket, circuit diagram in side.
Supplies two sets of batter pump and batter pipe.
Batter pump is rotor type of NISSIN brand.
PLC is SIEMENS 300; Transducer is SIEMENS; 10 inch color screen touch screen; SCHENEIDER contactor; trunking galvanized; Photo-electricity is supplied by SICK.
There is an automatic spurring-cleaned device at the bottom of the baking oven.
There is second pressure relief valve.
The floating system is stainless steel ball type.
The pressing system, opening system and tension system are improved about the heat-treatment. The main bolts are screws are 8.8 or 12.6 grade.
There is a safety cover for batter inductive switch.
There are safety windows at both sides of the baking oven.
The connecting system is “three-leaf” type.
All the belt rollers of the whole line are made from aluminium alloy.
All of motors, electric wire, and cable protection pipes accord with the UL standard.
The motors have the UL certificate, and the electric wire would be not visible.
The doors of electric cabinet can be opened only in case of the main power had cut off.
All weld is solderless joint.
Oil paint have not the lead.
All the doors are watertight doors.
Button Label use English.
Main technical parameter:
- Total quantity of GAS heated Baking Plates: 75pairs.
- Baking Plate Size: 470mm x 325mm
- Pattern of the wafer sheet: 2.5×2.5×0.5 (Standard), should be confirmed during one month after this contract signed, or the Seller has right to delay the delivery date.
- Wafer sheet weight: 50-65g
- Output: Up to 38 Sheets /min.
- LPG consumption: 20m³ / hour max.
- LNG consumption: 60m³ / hour max.
- Compressed air consumption: 0.2m³/min /0.8Mpa. Pressure
Location: Azusa, CA 91702
Skidding and Load out charges:
There will be loading and skidding charges added to your purchase at market rates for your convenience.
Food Processing, Packaging & Manufacturing Equipment
AUCTION DATE: lots start closing on Thursday, May 27th at 10:00 am PT
LOCATION: **Please note** Assets will be located at multiple locations.
Azusa, Calif.
INSPECTION: By appointment only. Please contact us to schedule. 818-495-3038
PICKUP: TBD
RIGGING:
There is no self-rigging. All Rigging and Load out will be completed by a contracted and approved Rigger.
18% Buyers Premium applies on all online purchases.
BidSpotter Customer Service Support Department
Have a question pertaining to the bidding process?
Visit our Frequently Asked Questions!
You can also start a live chat with a Bidspotter Support Representative by selecting Live Chat at the top of Bidspotter.com. More information on our chat system can be found by clicking here.
Customer Support Hours:
Email: support@bidspotter.com
Office: (253) 858-6777 Toll Free: (866) 597-2437
Terms of Sale Agreement:
SELLER RESERVES THE RIGHT TO ACCEPT OR REJECT ANY AND ALL BIDS
Inspection date (day only) is:
By Appointment Only. Call 818 495 3038 to Schedule.
Inspection locations:
Various Locations, call for specific item.
Inspection by appointment only.
Call or Email Logan Hillseth logan@chrishillsethenterprises.com or Patrick Hillseth at (818)495-3038 patrick@chrishillsethenterprises.com
Your question has been sent to the auctioneer.
There was an error sending your enquiry, why not try again later
1 Used All food equipment oven
Model: KHG-75
Quantity of GAS heated Backing Plates: 75 pairs.
Baking Plate Size: 470mm x 325mm
The pattern of the wafer sheet: 2.5×2.5×0.5 (Standard),
Wafer sheet weight: 50-65g
Output: Up to 38 Sheets /min.
LPG consumption: 20m³ / hour max.
LNG consumption: 60m³ / hour max.
Compressed air consumption: 0.2m³/min /0.8Mpa. Pressure
Burner Mfg.: Kehua
Materials: Pipeline is Stainless Steel, Burners are GG25 Precision cast iron
General Info:
The baking oven is the most important machine in the whole wafer production line. Its mechanical drive system uses baking tongs with hinges, which run on rails inside the oven, and baking plates are attached to the baking tongs. The speed of tong carriage is controlled by the frequency converter, the batter deposit system is batch-type, and the wafer baking system uses LPG for heating of the baking plates.
The functions of the baking oven are fully automatic from spreading batter on the plates until baked wafer sheets come out of the oven. The wafer sheets are baked evenly and produce good quality wafer sheets for the next procedure. There is a PID controller built into the PLC which is used to control the temperature of the baking plates automatically. The collection of the required signal of PID is supplied by an infrared sensor. The oven status display and the data reset are activated through the touch screen. All motors have a starting current protection and thermal overload protection. There’s also a ventilation door.
3-1. Model KHG-75 Gas Oven
The baking oven is the most important machine in the whole wafer production line. The oven is in wholly frame structure, which supplies enough support. Its mechanical drive system adopts baking tongs with hinges, which runs on the rails inside the oven and baking plates are installed in the baking tongs. The speed of tong carriage is controlled by the frequency converter, the batter deposit system is batch-type, and the wafer baking system uses LPG for heating of the baking plates. The functions of the baking oven is fully automatic from spreading batter on the plates through until baked wafer sheets come out of the oven. Bake the wafer sheets evenly and produces good quality wafer sheets for next procedure. In PLC there is a PID controller which is used for controlling the temperature of the baking plates automatically. The collection of required signal of PID is supplied by an infrared sensor. The oven status display and the data reset are supplied by a touch screen. All motors have the starting current protection and thermal overload protection. There’re ventilation door.
The gas accessories meet the standard of FM approval, and there’s one alarm if the gas leaking. There’re two ways of temperature controlling: one for testing the baking plates, another for testing the baking chamber, both of them can be showed of the touch panel and you just need to choose one. They’re sealed by silica gel.
There are two set of centrifugal fan on the top of oven for exhaust gas.
AC contactor is supplied by SCHENEIDER.
The stepping wheel bearings of the mould rack are supplied by SKF .
The pressing roller bearings are supplied by SKF.
Main Pneumatic components are supplied by FESTO.
The main drive reducing motor is supplied by SEW, in the front of baking oven with waste withdraw ahead and automatic tightening. Oven track is of 45#heat treatment, size 25X25.
The top of electrical cabinet is inclined 45 º, plus four Φ65 round leg (heigh 400 ). There’re data box, explosion-proof lamp, 2-3 socket, circuit diagram in side.
Supplies two sets of batter pump and batter pipe.
Batter pump is rotor type of NISSIN brand.
PLC is SIEMENS 300; Transducer is SIEMENS; 10 inch color screen touch screen; SCHENEIDER contactor; trunking galvanized; Photo-electricity is supplied by SICK.
There is an automatic spurring-cleaned device at the bottom of the baking oven.
There is second pressure relief valve.
The floating system is stainless steel ball type.
The pressing system, opening system and tension system are improved about the heat-treatment. The main bolts are screws are 8.8 or 12.6 grade.
There is a safety cover for batter inductive switch.
There are safety windows at both sides of the baking oven.
The connecting system is “three-leaf” type.
All the belt rollers of the whole line are made from aluminium alloy.
All of motors, electric wire, and cable protection pipes accord with the UL standard.
The motors have the UL certificate, and the electric wire would be not visible.
The doors of electric cabinet can be opened only in case of the main power had cut off.
All weld is solderless joint.
Oil paint have not the lead.
All the doors are watertight doors.
Button Label use English.
Main technical parameter:
- Total quantity of GAS heated Baking Plates: 75pairs.
- Baking Plate Size: 470mm x 325mm
- Pattern of the wafer sheet: 2.5×2.5×0.5 (Standard), should be confirmed during one month after this contract signed, or the Seller has right to delay the delivery date.
- Wafer sheet weight: 50-65g
- Output: Up to 38 Sheets /min.
- LPG consumption: 20m³ / hour max.
- LNG consumption: 60m³ / hour max.
- Compressed air consumption: 0.2m³/min /0.8Mpa. Pressure
Location: Azusa, CA 91702
General delivery information available from the auctioneer
Skidding and Load out charges:
There will be loading and skidding charges added to your purchase at market rates for your convenience.
Food Processing, Packaging & Manufacturing Equipment
AUCTION DATE: lots start closing on Thursday, May 27th at 10:00 am PT
LOCATION: **Please note** Assets will be located at multiple locations.
Azusa, Calif.
INSPECTION: By appointment only. Please contact us to schedule. 818-495-3038
PICKUP: TBD
RIGGING:
There is no self-rigging. All Rigging and Load out will be completed by a contracted and approved Rigger.
18% Buyers Premium applies on all online purchases.
BidSpotter Customer Service Support Department
Have a question pertaining to the bidding process?
Visit our Frequently Asked Questions!
You can also start a live chat with a Bidspotter Support Representative by selecting Live Chat at the top of Bidspotter.com. More information on our chat system can be found by clicking here.
Customer Support Hours:
Email: support@bidspotter.com
Office: (253) 858-6777 Toll Free: (866) 597-2437
Terms of Sale Agreement:
SELLER RESERVES THE RIGHT TO ACCEPT OR REJECT ANY AND ALL BIDS
Inspection date (day only) is:
By Appointment Only. Call 818 495 3038 to Schedule.
Inspection locations:
Various Locations, call for specific item.
Inspection by appointment only.
Call or Email Logan Hillseth logan@chrishillsethenterprises.com or Patrick Hillseth at (818)495-3038 patrick@chrishillsethenterprises.com