1298
Lot
1298
The baking oven is the most important machine in the whole wafer production line. The oven is in wholly frame structure, which supplies enough support. Its mechanical drive system adopts baking tongs with hinges, which runs on the rails inside the oven and baking plates are installed in the baking tongs. The speed of tong carriage is controlled by the frequency converter, the batter deposit system is batch-type, and the wafer baking system uses LPG for heating of the baking plates. The functions of the baking oven is fully automatic from spreading batter on the plates through until baked wafer sheets come out of the oven. Bake the wafer sheets evenly and produces good quality wafer sheets for next procedure. In PLC there is a PID controller which is used for controlling the temperature of the baking plates automatically. The collection of required signal of PID is supplied by an infrared sensor. The oven status display and the data reset are supplied by a touch screen. All motors have the starting current protection and thermal overload protection. There’re ventilation door.
The gas accessories meet the standard of FM approval, and there’s one alarm if the gas leaking. There’re two ways of temperature controlling: one for testing the baking plates, another for testing the baking chamber, both of them can be showed of the touch panel and you just need to choose one. They’re sealed by silica gel.
There are two set of centrifugal fan on the top of oven for exhaust gas.
AC contactor is supplied by SCHENEIDER.
The stepping wheel bearings of the mould rack are supplied by SKF.
The pressing roller bearings are supplied by SKF.
Main Pneumatic components are supplied by FESTO.
The main drive reducing motor is supplied by SEW, in the front of baking oven with waste withdraw ahead and automatic tightening. Oven track is of 45#heat treatment, size 25X25.
The top of electrical cabinet is inclined 45 º, plus four ?65 round leg (heigh 400 ). There’re data box, explosion-proof lamp, 2-3 socket, circuit diagram in side.
Supplies two sets of batter pump and batter pipe.
Batter pump is rotor type of NISSINbrand.
PLC isSIEMENS300; Transducer isSIEMENS; 10 inch color screen touch screen; SCHENEIDERcontactor; trunking galvanized; Photo-electricity is supplied by SICK.
There is an automatic spurring-cleaned device at the bottom of the baking oven.
There is second pressure relief valve.
The floating system is stainless steel ball type.
The pressing system, opening system and tension system are improved about the heat-treatment. The main bolts are screws are 8.8 or 12.6 grade.
There is a safety cover for batter inductive switch.
There are safety windows at both sides of the baking oven.
The connecting system is “three-leaf” type.
All the belt rollers of the whole line are made from aluminium alloy.
All of motors, electric wire, and cable protection pipes accord with the UL standard.
The motors have the UL certificate, and the electric wire would be not visible.
The doors of electric cabinet can be opened only in case of the main power had cut off.
All weld is solderless joint.
Oil paint have not the lead.
All the doors are watertight doors.
Button Label use English.
Main technical parameter:
Skidding and Load out charges:
There will be loading and skidding charges added to your purchase at market rates for your convenience.
Auction Date: lots start closing on Thursday, January 23rd at 10:00 am PST
Featuring Pharmaceutical Equipment & Machinery as well as Food Equipment, such as: High Capacity Granulation Machine, 20 Station Tablet Presses, Capsule Filling Machines, Tablet Counters, Encapsulators, Metal Inspection,Weight checkers, Coating Pans, Tablet/Capsule Counters, Pharma Pack Cotton Inserters, De-Duster Machines, Automatic Capsule Fillers, Blenders, Mills, Sorters and more.
***PLEASE NOTE***
Assets in this auction are located at various locations.
BidSpotter Customer Service Support Department
Have a question pertaining to the bidding process?
Visit our Frequently Asked Questions!
You can also start a live chat with a Bidspotter Support Representative by selecting Live Chat at the top of Bidspotter.com. More information on our chat system can be found by clicking here.
Customer Support Hours:
Email: support@bidspotter.com
Office: (253) 858-6777 Toll Free: (866) 597-2437
Terms of Sale Agreement:
SELLER RESERVES THE RIGHT TO ACCEPT OR REJECT ANY AND ALL BIDS
Inspection date (day only) is:
By Appointment Only. Call 818 495 3038 to Schedule.
Inspection locations:
Various Locations, call for specific item.
Inspection by appointment only.
Call or Email Randy Aguilar at (818)495-3038 randy@hillseth.com or Patrick Hillseth at (818)495-3038 patrick@chrishillsethenterprises.com
Your question has been sent to the auctioneer.
There was an error sending your enquiry, why not try again later
The baking oven is the most important machine in the whole wafer production line. The oven is in wholly frame structure, which supplies enough support. Its mechanical drive system adopts baking tongs with hinges, which runs on the rails inside the oven and baking plates are installed in the baking tongs. The speed of tong carriage is controlled by the frequency converter, the batter deposit system is batch-type, and the wafer baking system uses LPG for heating of the baking plates. The functions of the baking oven is fully automatic from spreading batter on the plates through until baked wafer sheets come out of the oven. Bake the wafer sheets evenly and produces good quality wafer sheets for next procedure. In PLC there is a PID controller which is used for controlling the temperature of the baking plates automatically. The collection of required signal of PID is supplied by an infrared sensor. The oven status display and the data reset are supplied by a touch screen. All motors have the starting current protection and thermal overload protection. There’re ventilation door.
The gas accessories meet the standard of FM approval, and there’s one alarm if the gas leaking. There’re two ways of temperature controlling: one for testing the baking plates, another for testing the baking chamber, both of them can be showed of the touch panel and you just need to choose one. They’re sealed by silica gel.
There are two set of centrifugal fan on the top of oven for exhaust gas.
AC contactor is supplied by SCHENEIDER.
The stepping wheel bearings of the mould rack are supplied by SKF.
The pressing roller bearings are supplied by SKF.
Main Pneumatic components are supplied by FESTO.
The main drive reducing motor is supplied by SEW, in the front of baking oven with waste withdraw ahead and automatic tightening. Oven track is of 45#heat treatment, size 25X25.
The top of electrical cabinet is inclined 45 º, plus four ?65 round leg (heigh 400 ). There’re data box, explosion-proof lamp, 2-3 socket, circuit diagram in side.
Supplies two sets of batter pump and batter pipe.
Batter pump is rotor type of NISSINbrand.
PLC isSIEMENS300; Transducer isSIEMENS; 10 inch color screen touch screen; SCHENEIDERcontactor; trunking galvanized; Photo-electricity is supplied by SICK.
There is an automatic spurring-cleaned device at the bottom of the baking oven.
There is second pressure relief valve.
The floating system is stainless steel ball type.
The pressing system, opening system and tension system are improved about the heat-treatment. The main bolts are screws are 8.8 or 12.6 grade.
There is a safety cover for batter inductive switch.
There are safety windows at both sides of the baking oven.
The connecting system is “three-leaf” type.
All the belt rollers of the whole line are made from aluminium alloy.
All of motors, electric wire, and cable protection pipes accord with the UL standard.
The motors have the UL certificate, and the electric wire would be not visible.
The doors of electric cabinet can be opened only in case of the main power had cut off.
All weld is solderless joint.
Oil paint have not the lead.
All the doors are watertight doors.
Button Label use English.
Main technical parameter:
General delivery information available from the auctioneer
Skidding and Load out charges:
There will be loading and skidding charges added to your purchase at market rates for your convenience.
Auction Date: lots start closing on Thursday, January 23rd at 10:00 am PST
Featuring Pharmaceutical Equipment & Machinery as well as Food Equipment, such as: High Capacity Granulation Machine, 20 Station Tablet Presses, Capsule Filling Machines, Tablet Counters, Encapsulators, Metal Inspection,Weight checkers, Coating Pans, Tablet/Capsule Counters, Pharma Pack Cotton Inserters, De-Duster Machines, Automatic Capsule Fillers, Blenders, Mills, Sorters and more.
***PLEASE NOTE***
Assets in this auction are located at various locations.
BidSpotter Customer Service Support Department
Have a question pertaining to the bidding process?
Visit our Frequently Asked Questions!
You can also start a live chat with a Bidspotter Support Representative by selecting Live Chat at the top of Bidspotter.com. More information on our chat system can be found by clicking here.
Customer Support Hours:
Email: support@bidspotter.com
Office: (253) 858-6777 Toll Free: (866) 597-2437
Terms of Sale Agreement:
SELLER RESERVES THE RIGHT TO ACCEPT OR REJECT ANY AND ALL BIDS
Inspection date (day only) is:
By Appointment Only. Call 818 495 3038 to Schedule.
Inspection locations:
Various Locations, call for specific item.
Inspection by appointment only.
Call or Email Randy Aguilar at (818)495-3038 randy@hillseth.com or Patrick Hillseth at (818)495-3038 patrick@chrishillsethenterprises.com