LOT OF HARDWARE, w/cabinets, assorted

LOT OF PALLET RACK, w/contents

LOT OF STEEL CARTS & STEEL WORKBENCH (3)

OVERHEAD HANDLING SYSTEM, GORBEL 113'L. X 10'-4"W., 10'-3" ht. under bridge, (4) 1,000 lb. cap. bridges w/Coffing 1,000 lb. elec. chain hoist

ROTARY SCREW AIR COMPRESSOR, SULLAIR 5500 S-ENERGY MDL. 5509/A, new 2002, 55 HP, variable spd., S/N 201202020046

ROTARY SCREW AIR COMPRESSOR, SULLAIR MDL. LS16-75H/A/SUL, 75 HP drive motor, air cooled, skid mtd., S/N 003-126492

CANTILEVER RACK

REFRIGERATED AIR DRYER, SULLAIR MDL. SR-400, new 2012, 400 CFM, inline filters, S/N 2128340005

VERTICAL AIR RECEIVER, STEEL FAB CO., new 2011, 150 PSI MAWP, 48" dia. x approx. 148" ht., on stand, S/N 668058

VERTICAL BANDSAW, ROLL-IN MDL. EF1459, new 2011, S/N 11044EF

HYDRAULIC SURFACE GRINDER, REID MDL. 618HYD, 1 HP direct drive spdl., 6" x 18" fine line electromagnetic chuck, 6" wheel, S/N 15989

ENGINE LATHE, HES 20" X 60" TYPE 550, 12.25” sw. over crosslide, 2.12" spdl. hole, spds: 36-1800 RPM, 12 HP, 2-axis D.R.O., 10" dia. 3-jaw Adjust-...

VERTICAL TURRET MILL, SHARP MDL. V2, new 2002, 12" x 58" table, 3-axis pwr. knee, spds: 80-4000 RPM, 7-1/2 HP drive, #40 NST spdl. taper, Newall 3...

JIB CRANE, GORBEL 500 LB. CAP. X APPROX. 12' REACH, 8' ht. under hook, Coffing 500 lb. cap. elec. chain hoist & pendant control

LOT OF FIXTURE BUILDING PARTS, assorted (on two skids)

MACHINE VISE, KURT 8"

{ Choice of lots: 117 } MACHINE VISE, KURT, 6" dia. 2-jaw

{ Choice of lots: 118, 119 } MACHINE VISE, KURT 6"

{ Choice of lots: 118, 119 } MACHINE VISE, KURT 6"

MACHINE VISE, KURT 6"

MACHINE VISE COMPOUND

ROTARY TABLE

CHUCK, 12" dia. 3-jaw

{ Choice of lots: 124 } CHUCK, BISON, 10" dia. 3-jaw

CHUCK, BISON, 8" dia. 3-jaw

{ Choice of lots: 126, 127 } CHUCK, BISON, 12" dia. 3-jaw

{ Choice of lots: 126, 127 } CHUCK, BISON, 12" dia. 3-jaw

{ Choice of lots: 128, 129, 130 } CHUCK, BISON, 10" dia. 3-jaw

{ Choice of lots: 128, 129, 130 } CHUCK, BISON, 10" dia. 3-jaw

{ Choice of lots: 128, 129, 130 } CHUCK, BISON, 10" dia. 3-jaw

CHUCK, BISON, 8" dia. 3-jaw

LOT OF CHUCKS (3), BISON, 8" dia. 3-jaw

LOT OF CHUCK JAWS, assorted

PRECISION VISE, 2"

{ Choice of lots: 135, 136 } LOT OF V-BLOCKS (4), 8" x 4" x 5-1/2"

{ Choice of lots: 135, 136 } LOT OF V-BLOCKS (4), 8" x 4" x 5-1/2"

{ Group of lots: 137, 138 } LOT OF V-BLOCKS (2), 4" x 4" x 3"

{ Group of lots: 137, 138 } LOT OF V-BLOCKS (2), 5" x 2-1/2" x 3-1/2"

LOT OF V-BLOCKS (10), assorted

DOUBLE SINE PRECISION PLATE, 5" x 5"

{ Choice of lots: 141, 142 } STUD SET, w/cart

{ Choice of lots: 141, 142 } LOT OF STUD SETS (5), w/cart

LOT OF STUD SETS, w/cart, assorted

{ Choice of lots: 143, 144, 145 } WORKBENCH, LISTA, 72" x 30" oak top, dbl. roller drawer pedestal

{ Choice of lots: 143, 144, 145 } WORKBENCH, LISTA, 72" x 30" oak top, dbl. roller drawer pedestal

{ Choice of lots: 143, 144, 145 } WORKBENCH, LISTA, 72" x 30" oak top, dbl. roller drawer pedestal

LOT OF ANGLE PLATES (2), 12" x 9" x 8"

LOT OF ANGLE PLATES, assorted

LOT OF PARALLELS, assorted

LOT OF 2-4-6 BLOCKS (8)

LOT OF 1-2-3 BLOCKS (10)

DEMAGNETIZER, 7" x 4"

{ Group of lots: 152, 153 } 5C SPIN INDEX FIXTURE, PHASE II

{ Group of lots: 152, 153 } 5C COLLET FIXTURE

LOT OF 5C COLLETS, w/holder, assorted

LOT OF PRECISION JACK SETS (6)

{ Choice of lots: 156, 160 } LOT OF CARBIDE ENDMILLS (in one box)

{ Choice of lots: 157, 158, 159, 161, 162, 163, 164, 165 } LOT OF CARBIDE ENDMILLS (in one box)

{ Choice of lots: 157, 158, 159, 161, 162, 163, 164, 165 } LOT OF CARBIDE ENDMILLS (in one box)

{ Choice of lots: 157, 158, 159, 161, 162, 163, 164, 165 } LOT OF CARBIDE ENDMILLS (in one box)