Battenfeld caterpiller dual belt puller saw combination, model DESC 125R, 5" wide x 70" long contact dual belt puller section, with saw attachment...

Model S45 Foremost Granulator, 16" x 45" feed opening, 3 knife closed rotor, 2 bed knives, feed hopper with dual 50 H.P. 230/460 volt motors, No b...

 Davis-Standard Gemini conical twin screw extruder, model GC8HD, 130/61 mm conical screws, counter rotating, electrically heated, air cooled barre...

100 MM Baker Perkins twin screw compounding extruder, Model MP-100MM-DE-XLT, 100MM/68.5MM tapered screws, co-rotating, electrically heated, water ...

Battenfeld planetary saw, model STU 250 E, range from 40 mm to 250 mm diameter pipe, approximately 8" diameter blade, pipe clamps, with Battenfeld...

Una Dyn Hopper Dryer with Heater and Blower, 200# Hopper with receiver. **Rigging Fee $50.00** ...[more]

Una Dyn Hopper Dryer with Heater and Blower, 200# Hopper with receiver. ...[more]

Gatto puller, model 203 3/26, 24" long x 2.75" wide smooth belts, manual gap adjustment, 2 hp dc motor, 440 volt, serial# 8711179. ...[more]

Lot of (2) 40 hp Baldor motors, 460 volt, 3 phase, 3530 rpm ...[more]

Conair stand pelletizer, model 3508, 8" wide helical rotor, pull roll assembly with rubber pull roll, 15 hp, 230 volt motor, serial# 12-080283. **...

Gatto vacuum tank, model DPC105.6.1, stainless steel construction, approximately 12" x 12" x 72" long chamber, single compartment with liquid ring...

Lorik puller, 3" wide x 12" long belts, smooth belts on base with 1.1 KW Servo motor. ...[more]

9 KW Sterlco temperature controller, type Sterltronic model M29412-AC, single zone, 230 volts, 3 phase with controls, serial# 95M5266. ...[more]

 Novatech hopper dryer system, model POD-250-B, rated 250 CFM, with blower, controls, 230 volt, with ten (10) Novatech hopper receivers model PEE-...

RDN cross cut travellilng saw, model C-430A, up to 6" high x 20" wide tubing size, up to 4" high x 30" wide profile size, approximately 18" table ...

Matthews Belt Puller, Model CL-650-VT, 4.5" wide x 42" long contact, flat belt, 4 speed transmission, 5 H.P. DC Motor, Serial No. 1584. ...[more]

Plastex Belt Puller, Type Cat 3, 4" wide x 44" long contact surface, flat belt, range 0" to 5.5" opening, adjustable height, on base with DC Motor...

Boston Matthews belt puller, model C110, approximately 24" long x 4" wide smooth belts with 1.5 kw, 220/440 volt motor drive with controller on st...

Stainless Steel Spin Dryer, 7.5 hp ...[more]

(2) unused 5 hp Aurora Centrifugal pumps, 208 volt ...[more]

Motan Diagnostic dryer, model MDD400, 21.6 KW total heater load, 8 hp total motor, 480 volt, wit (3) insulated hoppers with top mounted receivers,...

Novatec hopper dryer, model MDM-50A, 460 volt with 200# hopper with loader, 1.5" Killion extruder, model KN-150, 24:1 l/d, electrically heated, ai...

cooling tank, stainless steel construction, 4" x 4" x 11' long. ...[more]

model HC-18 Carr solid bowl centrifuge system, 18" titanium/316 stainless steel, hi-concentration model, unit has a vertical 18" ID bowl, 12" pool...

41" Contech Compusheeter, model CS-40. 40" wide, down acting scissor cut design with hydraulically driven rubber pull rolls, 2.5" diameter top rol...

Sakas Traveling Saw, 24" diameter blade, up cut design, approximately 17" travel, with approximately 7.5 HP motor, Serial No. S8-3741-6. **Rigging...

Technoplast puller/traveling saw combination, 7" wide x 72" long belt puller, chain driven, with dual pneumatic gap adjustment, with 14" diameter ...

RDN Flood Vacuum Sizer, Model 4D-3V-2T-15, 15' overall length, stainless steel construction, 5.5" diameter max. opening, 12" x 12" chamber, (1) 3'...

Gatto vacuum calibration tank, model DPC-104C-12-2, stainless steel construction, 12' overall length, 1' and 11' compartments, 8" x 8" cross secti...

Gatto vacuum calibration tank, model DPC-104C-12-2, stainless steel construction, 12' overall length, 1' and 11' compartments, 8" x 8" cross secti...

 2.5" Killion extruder, 24:1 L/D, electrically heated, air cooled, 40 HP DC motor with SCR controller, 9.3:1 gearbox ratio, (6) zone control panel...

Werner & Pfleiderer Coperion twin screw extruder, type ZSK-30, 30 mm diameter screws, co-rotating, electrically heated, water cooled barrel, 30:1 ...

12' long Stainless Steel Flood Cooling Tank, 12" x 12" chamber, 8" diameter max. opening, 2 compartment, adjustable height. **Rigging Fee $100.00*...

 PMC vacuum sizer, model 1-6V, stainless steel construction, 12" x 12" x 117" overall length, 3 compartment with 5 HP vacuum pump, 3 HP circulatio...

Gatto vacuum calibration tank, model DPC-104C-12-2, stainless steel construction, 12' overall length, 1' and 11' compartments, 8" x 8" cross secti...

2.5" Davis-Standard Mark V Extruder, Model DS2.5MS, 24:1 L/D, electrically heated, air cooled, jacketed feed section, 17.4:1 gearbox ratio, 40 HP ...