MECHANICAL SHEAR, NIAGARA 52" X 16 GA. MDL. 47078, 3 HP motor, sgl. phase, squaring arm, backgauge, blade, oil cups & grease fittings (squaring ar...

MECHANICAL SHEAR, GEO.A.O.H.L. & CO. 10' X 16 GA., 5 HP motor, sgl. phase, 0 deg. To 60 deg. blade, grease fitting, S/N 12646 (the end away from ...

MITERING BANDSAW, FMB TRITON, 3 phase, 1-1/2 HP motor, 2 spd. w/water, 8' to 10': 1" blade size, cutting capacities: 9.2" rounds, S/N 81043 (no s...

IRONWORKER, SCOTCHMAN 35 T. CAP. MDL. 314C, 3 HP motor, sgl. phase, 1" hole punch, 3/8" mild steel, 2" x 2" x 1/4" angle, flats; 1/2" x 6", 3/8" x...

NOTCHER, ROPER WHITNEY MDL. 100, 6" x 6" x 16 ga., hand operated (blades good, no base) Due to height, utility style trailers only! Must be remov...

ANGLE SHEAR, ROPER WHITNEY MDL. 379, 2" x 2" x 1/4", hand operated (blades good, no base) (Buyer must furnish all lumber & bolts for base of machi...

HOLE PUNCH, ROPER WHITNEY MDL. 20-S, 1/2" hole in 1/2" plate, hand operated (small amount of tooling, may need sharpening, no base) (Due to heigh...

FINGER BRAKE, CHICAGO DRIES & KRUMP MDL. BR4146, 4' x 14 ga., hand operated, S/N 315752 (all edges-good shape, all moving parts-tight) (Buyer must...

HAND HELD SHEAR, BOSCH 10 GA., 11/64" cap. in mild steel, S/N 0601-501-34 (used very little, extra blade) Due to height, utility style trailers o...

HAND NIBBLER BOSCH MDL. 060152034, 10 ga., 9/64" cap. In mild steel (used very little) (Must be removed by April 13 or a storage fee will be charg...

PEDESTAL GRINDER, CLARK MDL. 36191, 3-phase, 2 HP motor, 12 max. wheel, S/N 36191 (runs good, 9" rock, 12" brush) (Must be removed by April 13 o...

MILLING VISE, swivel base, 2" jaw depth, 5-1/8" jaw opening, 7" jaw width (needs new handle) (Must be removed by April 13 or a storage fee will b...

HAND WINCH, w/handle, worm gear driven (Must be removed by April 13 or a storage fee will be charged) (Location 13)

MOTOR, CENTURY MDL. CS231-HCA6-011697-00, 2 HP, 220 v., 1,750 RPM (grease zerts at bearings) (Must be removed by April 13 or a storage fee will b...

LOT OF WELDING LEADS: 121' of 1/0, 300 amp electro horder & LC40 connector on ends (very good shape) (Must be removed by April 13 or a storage fee...

LOT OF WELDING LEADS: 125' of 2/0, LC40 connector on other end (jacket of 2/0 has misprint - says 1/0 because welding supply had to sell as a 1.0,...

AIR COMPRESSOR, INGERSOLL RAND MDL. 225X5, Type 30, 3-belt pulley, S/N 30T54547 (Must be removed by April 13 or a storage fee will be charged) (L...

FORKLIFT, TOWMOTOR 9,000 LB. CAP. MDL. 600SLP9024, 9,000 lb. cap. @ 24" L.C., 6 cyl. motor, triple mast, 182" ht., 48" forks, S/N 600S0229 (motor...

OPEN JAW PIPE VISE, COLUMBIAN 3" (Must be removed by April 13 or a storage fee will be charged) (Location 13)

ROD VISE, TOLEDO 2-1/2", Mdl. 1445 (Must be removed by April 13 or a storage fee will be charged) (Location 13)

LOT OF OXY./ACY. HOSE (50'), 1/4" (Must be removed by April 13 or a storage fee will be charged) (Location 13)

BOOMER/BINDER, LEBUS TYPE L, 3/8" to 1/2" chain (Must be removed by April 13 or a storage fee will be charged) (Location 13)

SNATCH BLOCK, 3/8" to 7/16", for cable (Must be removed by April 13 or a storage fee will be charged) (Location 13)

HYDRAULIC MOTOR/PUMP, ORBMARK MOTORS MDL. 12/85, 5/8" shaft, S/N 116W4F (Must be removed by April 13 or a storage fee will be charged) (Locatio...

TROLLEY, YALE 2 T. CAP., Mdl. T, fits 8" to 10" I-beam (Must be removed by April 13 or a storage fee will be charged) (Location 13)

TROLLEY, THE HARRINGTON CO. 1-1/2 T. CAP., Mdl. J, fits 6" I-beam (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 9", 2-belt, 1-1/8" bore (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 9", 1-belt, 1" bore (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 7", 2-belt, 1" bore (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 7", 2-belt, 1-1/8" bore (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 7", 2-belt, 1-1/8" bore, interchangeable hub (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 7-1/2", 2-belt, 3/4" bore, interchangeable hub (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 6-1/2", 3-belt, 1-3/8" bore, interchangeable hub (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 6", 3-belt, 1-3/8" bore, interchangeable hub (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 6", 3-belt, 1-1/4" bore, interchangeable hub (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 3-1/4", 4-belt, 1-3/8" bore, interchangeable hub (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 4-3/4", 3-belt, 1-1/16" bore, interchangeable hub, extra hub w/1" bore (Must be removed by April 13 or a storage fee will be charged) (...

PULLEY, 4-1/4", 3-belt, 3/4" bore, interchangeable hub (Must be removed by April 13 or a storage fee will be charged) (Location 13)

PULLEY, 3-3/4", 3-belt, 3/4" bore, interchangeable hub (Must be removed by April 13 or a storage fee will be charged) (Location 13)

LOT OF TAKE-UP BEARINGS (2), for 1-1/2" shaft, w/(2) 1" x 10" all thread shafts & nuts (Must be removed by April 13 or a storage fee will be char...

LOT OF PILLAR BLOCK BEARINGS (5), for 1" shaft (Must be removed by April 13 or a storage fee will be charged) (Location 13)

LOT OF BOLT FLANGE BEARINGS (4), for 1-1/4" shaft (one flange has broken corner but still intact) (Must be removed by April 13 or a storage fee w...

DRILL PRESS, 12-speed, Mdl. BDM-58-12S, 5/8" cap., 3/4 HP motor, #2 MT spdl., (2) chucks, key, S/N 000222 (Must be removed by April 13 or a stor...

DRILL PRESS, DELTA NO. 782, #2 MT spdl., 3/4 to 1 HP motor, (5) bits, chuck, custom table on stand (in need of repair) (Must be removed by April ...

HYDRAULIC PUMP, 7/8" shaft (Must be removed by April 13 or a storage fee will be charged) (Location 13)

HYDRAULIC PUMP, 3/4" shaft, S/N 1293461K9 (Must be removed by April 13 or a storage fee will be charged) (Location 13)

HYDRAULIC PUMP, VICKERS MDL. D210-11-0012S6, 3/4" shaft (Must be removed by April 13 or a storage fee will be charged) (Location 13)

WELDING MACHINE, AIRCO MDL. AIRCOMATC MIDGET CAR II 250 AMPS DC, Mdl. AH20-E MIG gun, 1 & 2 lb. spools, .035 to .045, 50' lead, no base or stand,...

T-SLOTTED FLOOR PLATE, 10' x 5' x 1' (Location 16 - this location will load for free on customer provided vehicles.)

T-SLOTTED FLOOR PLATE, 10' x 5' x 1' (Location 16 - this location will load for free on customer provided vehicles.)

T-SLOTTED FLOOR PLATE, 10' x 5' x 1' (Location 16 - this location will load for free on customer provided vehicles.)

T-SLOTTED FLOOR PLATE, 10' x 5' x 1' (Location 16 - this location will load for free on customer provided vehicles.)

T-SLOTTED FLOOR PLATE, 10' x 5' x 1' (Location 16 - this location will load for free on customer provided vehicles.)

T-SLOTTED FLOOR PLATE, 10' x 5' x 1' (Location 16 - this location will load for free on customer provided vehicles.)

T-SLOTTED FLOOR PLATE, 10' x 4' x 1' (Location 16 - this location will load for free on customer provided vehicles.)

T-SLOTTED FLOOR PLATE, 10' x 4' x 1' (Location 16 - this location will load for free on customer provided vehicles.)

T-SLOTTED H.D. SETUP TABLE, 10'-7" x 4' x 4', approx. 10,000 lb. (Location 16 - this location will load for free on customer provided vehicles.)

T-SLOTTED SETUP FIXTURE, 13' x 41" x 20", approx. 15,000 lb. (Location 16 - this location will load for free on customer provided vehicles.)

T-SLOTTED FIXTURE (2), 6' x 2' x 2' , (Note: one table is broken on corner) (Location 16 - this location will load for free on customer provided v...

T-SLOTTED FLOOR PLATE, 5' x 37" x 30" (Location 16 - this location willl load for free on customer provided vehicles.)